Ekosaputro83’s Weblog

NOTE : Set the SCSI I.D. of the disc you want to copy to “ 1 ” ( by select the Rotary Switch at the rear of the unit to number “1”, this equates to address 0402 ).

Place the disc into the slot labelled 0402 in disc unit assembly , then turn “on” and allow the disc to run up to normal speed.

At the SCICLONE P.C. , Stop the Simulator Program by type :
Command > RUN SIMSTOP <cr>

1) At the CONSOLE Data Terminal , Panel Mode the Host computer using :
@@P , HALT , RST , CLE , IPL=0400
( then enter date and time ……… etc.)

2) Still at the CONSOLE Data Terminal , type :
@@A
OWNERNAME : SYSTEM <cr>
ENTER KEY : <cr>

3) At SSM , then select “ T ” <cr> ——> ( togo to TSM prompt )
TSM> MIRROR <cr>

This will prompt you to confirm that you are about to Copy Files in the disc I.D.= 0400 ( as a MASTER ) into the disc I.D.= 0402.
You are about to mirror DM0400 disc to the DM0402 disc
Is it safe to countinue? Y/N> Y <cr>
“DISC MIRROR IN PROGRES …….”

Check the “Red disc acces light” on the front of the disc drives start flashing.
Approximately 30 Minutes later ………… , the CONSOLE Data Terminal screen will tell you that the Mirror Disc procedures has finished.
** VOLUME FORMATTER 3.4U01.04 **
Confrim = no
Volume name = 5195.3
Name of divace to be formated = DM0402
System image file = @5193.3 (system)5183-507
Bootstap file = @ ( )
Device = DM0402—VOLUME FORMATTING SUCCESS FULLY COMPLETED
TSM>……..

4) If finish select “ X “ to exit from TSM prompt.

Remove the disc from I.D.=0402 , then set the Rotary switch on the back of this unit back to “0“.
Replace the MASTER Disc (ID=0400) and install the Disc you have just copied into ID=0400.

Boot the Simulator Program as normal procedure and Check if the Simulator works correctly.

1. Place & Prepare the SCSI Disc into slot labelled 0400 in disc unit
2. Place & Prepare the SDT Tape into Magnetic Tape Unit
3. At the Operators CONSOLE Data Terminal

@@P
// HALT <cr>
// RST <cr>
// CLE <cr>
// IPL=1000 <cr> —–> It will load the SDT Files from MTU :
System will responds with …………………
Memory Initialization Started ……………..Completed
Enter date and time :

FMT >
FMT > FORMAT DEVICE = DM400 VOLUME =5195.3 MAXRES=20000

It will report details to screen
Ensure no error massages

ENTER SYSTEM VOLUME CHANNEL AND SUB ADDRESS : 0400

VOL> CREATE D SYSTEM ENTR=10000

This will create the system directory of a suitable size which is required before beginning to restore from SDT tape.

VOL> RES restore first image

VOL> RES restore second image

Report RES until end of SDT tape

(REBOOT)
@@P
// HALT <cr>
// RST <cr>
// CLE <cr>
// IPL=1000 <cr>

Login as SYSTEM on user terminal (NOT CONSOLE)

TSM>

1. Place & Prepare the SCSI Disc into slot labelled 0400 in disc unit
2. Place & Prepare the Diagnostic Tape into Magnetic Tape Unit
3. At the Operators CONSOLE Data Terminal

@@P
// HALT <cr>
// RST <cr>
// CLE <cr>
// GPR0=1 <cr> —–> GPR0=1 to disable auto diagnostic
// IPL=1000 <cr> —–> It will load the Diagnostic Files from MTU :
- For Level 1 : under Diagnostic Overlay Loader ( DOL > )
- For Level 2 : under Diagnostic eXecutive Program ( DXP > )

System will responds with …………………
Memory Initialization Started ……………..Completed
Gould Diagnostic Loader ………….. ……..etc

DOL >
DOL > SHOW FILES <cr > —-> To see the Diagnostic Files Listing
DOL > LOAD CV.DXP <cr > —-> To go to “Level 2” Diagnostic —-> ( DXP > )

System will responds with ….
* LOADED : ‘CV.DXP.M’
PGM:03000

DOL > START <cr >

System will responds with ….
 Default Real-Time Clock Rate = 60Hz ; [ cr , # ] ? 50 <cr>
 Default Time-of-Day = 00:00:30 ; [ cr , HH:MM:SS ] ? ( you can typeTime if needed ) <cr>
 Do you need Help ; [ Y , N ] ? ( you can type “Y” or “N” if needed ) <cr>

DXP > SHOW FILES <cr > —-> To see the Diagnostic Files Listing

DXP > LOAD LTC(RP.MVP) <cr > —> To load the MVP Program with name “LTC”

Then answer the questions with ….
 C < cr > —-> Continue the MVP program loading
 < cr > —-> Default answer = “TY7EFC”
 < cr > —-> Default answer = “N”
 04 < cr > —-> Disc Processor Address = “04” ( IPL=0400 )
 < cr > —-> Default answer = “MPX”
 0,8155,N < cr > —-> Disc Address = “0”, Model = “8155”, Dual = “N”
 < cr > —-> Default answer
DXP > START LTC <cr > —-> To Start the MVP program with name “LTC”

Then answer the questions with ….

 1 < cr > —-> Select Format procedure from the menus
 F < cr > —-> Continue to Format the Media Disc